Guidelines For Post-Dive Equipment Care
Guidelines For Post-Dive Equipment Care
By Jessica Vyvyan-Robinson
If you own scuba equipment, knowing how to properly take care of it after a dive is crucial. Not only does good post-dive maintenance increase the lifespan of expensive equipment, but it also minimizes the risk of gear-related issues the next time you dive. Our equipment is our lifeline underwater, so keeping it in working order is of paramount importance. Basic rules apply to the post-dive maintenance of all scuba gear, including rinsing items thoroughly with fresh water after a dive, and allowing them to dry completely before being packed away. Dive gear should never be left in direct sunlight for prolonged periods of time, as sunlight can degrade, crack or fade materials, including neoprene and rubber. Specific considerations relate to particular pieces of equipment, most of which are listed below.
Like the rest of your scuba equipment, your regulator needs to be rinsed in fresh water at the end of the day’s diving. Make sure that no water enters the regulator’s first stage, as it’s internal components are susceptible to damage when exposed to moisture —allowing them to get wet will most likely result in an expensive trip to an equipment technician. Before rinsing, replace and securely fasten your regulator’s dust cap, first ensuring that the dust cap itself is dry. You can do this by using compressed air from your cylinder to blast excess water from the dust cap before fastening it in place, but that method’s not without detractors.
Instead of leaving your first stage to soak in fresh water, rinse it thoroughly under the tap; this will safeguard against water seeping past the dust cap. Alternatively, you can fully submerge your regulator if the first stage is still attached to a pressurized cylinder, which will prevent any water from entering the system. Do not press the purge button on either your primary second stage or your octopus while you are washing your regulator, as this will also allow water to enter the first stage. If you have hose protectors, make sure that you rinse underneath them during the cleaning process; similarly, move your low-pressure inflator connector back and forth to remove any salt, grit or sand. This way, even the least visible parts of your regulator will be kept corrosion free, and will continue to perform as they should. Once you have finished rinsing your regulator, hang it up and allow it to dry completely before packing it away.
When it comes to washing your BCD, it’s hugely important to remember the inside after having thoroughly rinsed the exterior. During a dive, salt water leaks into the BCD through the dump valves and the low-pressure inflator, and must be drained out during your post-dive maintenance routine. To do this, use a hose to flush fresh water into the BCD’s bladder via the low-pressure inflator, making sure to hold down the deflate button as you do so. Allow the water to flow into the BCD until it is approximately one quarter full, and then orally inflate it. This will allow the water to easily circulate around the inside of the BCD. Then, shake it to make sure that the water reaches every part of the jacket before allowing the water to drain through the dump valves, simultaneously rinsing them too. You can repeat this process several times before inflating the BCD partially and storing it. Ideally, you should keep your BCD hung up in a cool, dry place; the partial inflation will prevent the insides of the BCD from sticking together.
Wetsuit, booties, hoods and gloves
All of these items should be washed both on the inside and on the outside. It’s a good idea to use soap or disinfectant to eliminate any odors, but make sure that you buy one that’s appropriate for use on neoprene. Wetsuit soap is readily available at most dive centers or equipment stores; rinse it off with more fresh water once used. After cleaning your wetsuit and other neoprene items, hang them up to dry completely before packing them away. If you don’t, mildew and other bacteria will develop, degrading the quality of your equipment and causing it to smell. The best way to store a wetsuit is to hang it up, preferably on a purpose-built wetsuit hanger. Do not use wire hangers, as they will crease and mark your suit — the wider the hanger, the better. For transporting your suit or for storing it for short periods of time roll it rather than folding it. Folds can cause creases in the neoprene that may not come out, and make the suit uncomfortable to wear. It is also a good idea to lubricate the zips on your wetsuit or booties, ideally with zipper wax specifically made for this purpose.
Many divers overlook their cylinders when it comes to post-dive care, but they also need to be rinsed with fresh water. This prevents salt buildup and consequent corrosion, and also displaces grit and sand from around the tank valve; if left, these particles can make it difficult to turn your air on and off. You should never put a cylinder into storage either emptied or filled completely. When empty, the absence of pressure can make it easy for contaminants to enter the cylinder; if stored too full they can eventually crack over time. They should be stored lying horizontally, or in a secured upright position to prevent them from falling and becoming damaged.
Mask, fins and snorkel
Your soft gear is easily maintained; like everything else, it must be rinsed in fresh water, dried and put away carefully. Your mask should be packed in a hard case to protect the lenses from scratches and the mask itself from possible impact. Make sure that any other items that you store with your mask (e.g. dive computer, compass) do not bend, squish or deform the silicone; otherwise, your mask’s shape could be altered causing it to leak or become uncomfortable. Similarly, save the plastic inserts that come with your fins when you buy them, and replace during storage to retain the shape of your fins’ foot pockets. Do not store your fins by balancing them on their tips, as this can also cause distortion and diminished performance. Instead, keep them lying flat, or hung by the strap on a wide peg.
Each of your dive accessories has unique care requirements. Underwater cameras, for example, have a lengthy post-dive care regime. They must be left to soak for as long as possible in fresh water, to allow all salt to dissolve from the housing. You should gently work all of the housing’s moving parts to dislodge any salt, grit or sand stuck beneath them. Once you are satisfied that the housing is salt-free, you must dry it completely before opening it to remove your camera. You should remove your batteries and memory card from the camera, and make sure to wipe clean and lubricate all O-rings. Do not store your housing with the main body O-ring in place, as the constant pressure will eventually change the shape of the O-ring and reduce its ability to create a sufficient seal. Instead, remove the O-ring carefully, clean it and store it with the rest of your equipment in a sealed plastic bag. Strobes and underwater torches should be treated similarly — wash, dry, remove batteries, then clean and lubricate all O-ring.
When washing your dive computer, make sure to depress all the buttons while holding the computer underwater in order to flush salt deposits from beneath them. Rinsed and dry dive knives thoroughly, then apply a thin coating of silicone grease to the blade before storage to prevent rusting. All other diving equipment, including signal marker buoys, compasses, whistles and octopus attachments should be rinsed at the same time as the rest of your gear, and stored appropriately.
No matter how diligently you take care of your equipment, make sure to fully check and test your gear before use to ensure that it’s in full working order. Above all, remember that by properly looking after your dive equipment, you are allowing it to continue looking after you.